EFFICIENT UTILIZATION OF COTTON ROVING WASTE AS A SECONDARY RAW MATERIAL

Authors

  • Tolibjonova Hadicha Sherali qizi Namangan State Technical University, Uzbekistan Author

Keywords:

cotton roving waste, secondary raw material, mechanical recycling, fiber recovery, recycled cotton, roving recycling, cotton spinning, yarn quality, waste utilization.

Abstract

Cotton roving waste is a pre-consumer fibrous waste generated during roving preparation, machine stoppages, roving breakages and material handling in cotton spinning mills. Because this waste contains reusable cotton fibers, its recovery and reintegration into textile production can reduce the consumption of virgin raw materials and improve material efficiency. Previous investigations have shown that roving waste may represent approximately 3.5–5.2% of production volume in spinning mills, with mechanical inefficiencies, operator handling errors and raw-material variability identified as the principal causes of waste generation [1]. Other research has reported that roving waste can contain a high proportion of usable fibers and can therefore be considered a valuable secondary raw material [2]. This paper analyzes the technological potential of cotton roving waste as a secondary raw material, focusing on mechanical recycling, fiber recovery, blending and subsequent spinning. The results of previous experimental studies indicate that an improved mechanical processing machine achieved a fiber recovery rate of up to 80%, while yarn containing up to 20% recycled roving fibers demonstrated acceptable tensile strength and evenness for medium-count yarns [3]. Research on other cotton waste streams also confirms that controlled mechanical processing and appropriate blending ratios are important for maintaining yarn quality [5–10]. The analysis demonstrates that efficient utilization of roving waste requires controlled opening and cleaning, preservation of useful fiber length and appropriate blending with virgin cotton.

References

1.Alikhonov, S. (2025). Utilization of Cotton Roving Waste in Spinning. Web of Technology: Multidimensional Research Journal, 3(9), 12–15.

2.Alikhonov, S., & Bobojanov, H. (2025). Roving Waste in Textile Manufacturing: Generation, Management, and Sustainable Solutions. Web of Scientists and Scholars: Journal of Multidisciplinary Research, 3(9), 56–60.

3.Alikhonov, S. S. (2026). Cost Reduction Strategies through Efficient Roving Waste Recycling in Spinning Mills. International Conference on Multidisciplinary Science, 4(3), 9–11.

4.Alikhonov, S. S., & Bobojanov, K. T. (2026). Mechanical vs. Solvent-Based Recycling Technologies for Roving Waste: A Comparative Review. International Conference on Multidisciplinary Science, 4(3), 12–14.

5. Bedez Ute, T., Çelik, P., & Uzumcu, M. B. (2019). Utilization of Cotton Spinning Mill Wastes in Yarn Production. In Textile Industry and Environment. IntechOpen. DOI: 10.5772/intechopen.85127.

6.Ütebay, B., Çelik, P., & Çay, A. (2019). Effects of cotton textile waste properties on recycled fibre quality. Journal of Cleaner Production, 222, 29–35. DOI: 10.1016/j.jclepro.2019.03.033.

7.Kanan, M., Wanassi, B., Azzouz, B., Ben Hassen, M., Assaf, R., & Barham, A. S. (2024). Cotton recycling: An experimental study of the mechanical preparation process. Case Studies in Chemical and Environmental Engineering, 10, 100849. DOI: 10.1016/j.cscee.2024.100849.

8.Halimi, M. T., Ben Hassen, M., Azzouz, B., & Sakli, F. (2007). Effect of cotton waste and spinning parameters on rotor yarn quality. The Journal of The Textile Institute, 98(5), 437–442. DOI: 10.1080/00405000701547649.

9.Wanassi, B., Azzouz, B., & Ben Hassen, M. (2016). Value-added waste cotton yarn: Optimization of recycling process and spinning of reclaimed fibers. Industrial Crops and Products, 87, 27–32. DOI: 10.1016/j.indcrop.2016.04.020.

10.Krupincová, G. (2024). Assessment of the effects of the use of preconsumer cotton waste on the quality of rotor yarns. Heliyon, 10(15), e34482. DOI: 10.1016/j.heliyon.2024.e34482.

Downloads

Published

2026-10-09