INTEGRATED DESIGN, OPTIMIZATION AND MECHATRONIC CONTROL OF A FOUR-SECTION ULTRASONIC AEROSOL HUMIDIFICATION SYSTEM FOR COTTON LINT BEFORE BALING

Authors

  • Rasul Karimovich Tadjibaev¹ · Zaylobiddin Obbosbek ugli Rakhmonov² Sayidmurodov Mirzohid Mirzaraximovich3 ¹Professor, Fergana State Technical University; ²PhD researcher, Fergana State Technical University | Fergana, Uzbekistan ,3PhD in Technical Sciences, Associate Professor at Namangan State Technical University, Author

Keywords:

cotton lint; ultrasonic atomization; cross-flow humidification; GAB–LDF model; Box–Behnken design; PLC control; air recirculation.

Abstract

This study integrates the theoretical design, operating-regime optimization, mechatronic control and energy assessment of a four-section ultrasonic aerosol humidifier for cotton lint before baling. Fine mist is produced by piezoelectric atomization and carried in conditioned air through a moving lint layer, with flow direction alternating between consecutive sections. A sorption–transport model is linked to a three-factor Box–Behnken response analysis, while feedforward and feedback control are evaluated using a delay-based simulation. The source-reported factor–response pairs show close agreement between calculated and experimentally labelled values, and the modeled chamber substantially improves moisture uniformity relative to one-sided treatment. Air recirculation is predicted to reduce the required mist output and heating duty. The study differentiates direct source-reported observations from mathematical predictions, controller simulations and engineering estimates. The integrated findings provide a design basis for prototype validation and industrial implementation.

References

1.Gordon, S., Horne, S., van der Sluijs, R. (2007). Moisture in cotton ginning review: Final report, CRDC Project CTFT20. Cotton Research and Development Corporation.

2.Chun, D.T.W., Anthony, W.S. (2004). Effects of adding moisture at the gin lint slide on cotton bale microbial activity and fiber quality. Journal of Cotton Science, 8, 83–90.

3.Rutherford, R.D. et al. (2013). Field evaluation of the Lummus bale moisture monitor. Proceedings of the Beltwide Cotton Conferences, 1215–1220.

4.Montalvo, J.G., Von Hoven, T.M. (2008). Review of standard test methods for moisture in lint cotton. Journal of Cotton Science, 12, 33–47.

5.Lang, R.J. (1962). Ultrasonic atomization of liquids. Journal of the Acoustical Society of America, 34(1), 6–8.

6.Rajan, R., Pandit, A.B. (2001). Correlations to predict droplet size in ultrasonic atomisation. Ultrasonics, 39(4), 235–255.

7.Hinds, W.C. (1999). Aerosol Technology: Properties, Behavior, and Measurement of Airborne Particles, 2nd ed. Wiley.

8.ASHRAE (2017). Handbook—Fundamentals, Chapter 1: Psychrometrics. ASHRAE.

9.Timmermann, E.O. (2003). Multilayer sorption parameters: BET or GAB values? Colloids and Surfaces A, 220, 235–260.

10.Crank, J. (1975). The Mathematics of Diffusion, 2nd ed. Clarendon Press.

11.Box, G.E.P., Behnken, D.W. (1960). Some new three level designs for the study of quantitative variables. Technometrics, 2(4), 455–475.

12.IEC (2013). IEC 61131-3: Programmable controllers—Part 3: Programming languages.

13.Åström, K.J., Hägglund, T. (2006). Advanced PID Control. ISA.

14.Skogestad, S. (2003). Simple analytic rules for model reduction and PID controller tuning. Journal of Process Control, 13(4), 291–309.

15.ASTM International. ASTM D2495: Standard Test Method for Moisture in Cotton by Oven-Drying.

Downloads

Published

2026-05-30